Zinc coated steel

The dynamic resistance profiles of low carbon steel , zinc coated steel , stainless steel , aluminum alloy and nickel-base alloy have been studied .

目前，已对低碳钢、镀锌钢板、不锈钢、铝合金和镍合金等材料点焊时的动态电阻变化规律进行了研究。

The effect of TiC coating in electrode tip surface on spheriform electrode degradation during resistance spot welding zinc coated steel was investigated by SEM , EDX and XRD .

利用SEM、EDX和XRD等方法分析了在点焊镀锌钢板时球形电极表面熔敷TiC涂层对电极失效的影响。

Study on laser welding of zinc coated steel and the effects of zinc vaporization

镀锌板激光焊接工艺及锌行为研究

The Emulated Testing Device for Hot Zinc Coated Steel Plate By Using Delphi

采用Delphi的热镀锌钢板模拟试验装置

Analysis of Electrode Failure during Resistance Spot Welding of Zinc Coated Steel Using Cu / TiB_2 Electrodes

TiB2/Cu复合材料作电极点焊镀锌钢板的失效分析

Electro-galvanized Steel Sheet / Electrolytic Zinc Coated Steel Sheet

电镀锌钢片或电解钢片GB/T15393-1994钢丝镀锌层

HDPE with zinc coated steel nail .

HDPE及优质镀锌钢钉。

The experiment result proved the technological feasibility of laser butt welding for thin zinc coated steel sheets whose edges are prepared by laser cutting on the same laser processing equipments .

试验结果表明，镀锌板的激光剪裁拼焊接头性能符合实际使用要求，在同一台激光加工设备上实现镀锌板的激光切割剪裁后再直接进行激光拼焊的工艺方法是可行的。

Deep cryogenic treatment is a very effective method for improving the electrode life of aluminum and hot zinc coated steel . Yet , the mechanism of nonferrous properties improved by deep cryogenic treatment is not clear for certain nonferrous materials .

深冷处理可以提高Cu-Cr-Zr合金电极使用寿命，但目前对于有色金属深冷处理改善性能的机理还不十分清楚。

Aluminum - zinc alloy coated steel sheet for construction

建筑用镀铝锌钢板

Study on laser brazing of zinc - coated steel with filler wire

镀锌板填丝激光钎焊工艺的初探

Among zinc coated auto steel sheets , IF steel takes a larger portion , therefore , its mechanical performance improvement becomes a key in solving quality problems of products .

而热镀锌汽车板产品中IF钢所占比例较大，所以IF钢性能改进成为生产重点解决问题。

The results show that electrode degradation mechanism was basically caused by wear due to fracture of local welding between the electrode tip surface and zinc coated sheet steel happen at electrode surface and alloying between electrode and zinc on zinc coated steel during resistance spot welding zinc coated steel .

结果表明：点焊镀锌钢板时电极的失效机制主要是电极和镀锌板之间局部焊接的断裂发生在电极表面而导致的电极磨损以及电极和镀锌板表面的锌之间的合金化。

Actual thermal cycling curve of welded seam of laser welding is obtained to zinc coated high strength steel .

对激光焊接高强度镀锌钢板时接头上热循环作了试验测定，测出了焊缝热影响区的实际热循环曲线。

Laser welding of zinc coated high strength steel relate to the impact of plasma , grain growth of HAZ .

高强度镀锌钢的激光焊接关键涉及光致等离子体的影响；

Continual hot-dip aluminium zinc silicon alloy coated steel strips and sheets Dual-Reduction Tinplate

GB/T14978-1994连续热浸镀铝锌硅合金镀层钢带和钢板双相辗压镀锡薄钢片

The result of a neutral salt spray test for 48 hours indicate that aluminum coated carbon steel tubes are more corrosion resistant than zinc coated low carbon steel tubes .

48h的中性盐雾试验结果显示热浸镀铝低碳钢管的耐蚀性远优于镀锌钢管。

Based on many experiments of CO_2 laser welding of 1.5 mm zinc coated high strength steel to vehicle body , joint microstructure and stress-strain curve of specimen are acquired . Using T.

利用CO2激光对汽车车身用1.5mm厚高强度双面镀锌钢进行了大量的焊接实验，对焊缝组织进行了显微组织分析和相关的机械性能实验。

The experimental result indicates that deep penetration laser welding can effectively avoid softening HAZ , control the gas hole and restrain joint flaw of welding of zinc coated high strength steel by blowing coaxial and side protective gas .

研究结果表明：在同轴和侧吹保护气体的条件下，激光深熔焊接能有效地避免高强度镀锌钢热影响区（HAZ）的软化，控制焊缝气孔及焊接接头裂纹的产生。